Finalised drilling pilot side of the roll bar using the same technique with the drill hole duplicator.
Double checking the 7/32 spacing between the side of the F-721B-L canopy deck and the WD-641 roll bar.
TitleGarrison
“No bird ever flew nonstop from New York to Tokyo, or raced 15 miles high at triple the speed of sound.
But birds do something else.
They do not conquer the air; they romance it..”
Peter Garrison
HoursAndCounting
Jur's RV7 Aircraft Factory
2917 hours and counting
Some decisions in life are bare of any obvious logic
Articles in Finish Kit
-
1. Various Finishing
- 10/05/2019 - Finising kit arrived !
- 11/05/2019 - Finish kit inventory - 4h
- 29/07/2020 - marking and drilling access plates - 2h
- 30/07/2020 - cutting access plate covers - 2h
- 21/08/2020 - cleanup deburr the cover plates - 4H
- 17/09/2022 - ADAHRS bracket prep - 5h30
- 31/03/2023 - Various tasks -1h
- 28/08/2023 - Inforcement bracket top fuselage rib - 3h
- 29/10/2023 - Aileron Trim 1 - 5h30
- 30/10/2023 - Aileron Trim 2 - 2h
- 01/11/2023 - Aileron trim 3 - 2h30
- 03/11/2023 - Elevator trim - 2h
- 02/12/2023 - Aileron Trim 4
-
2. Engine mount
-
3. Slider Canopy
- 24/08/2020 - Bending and drilled pilot holes rollbar - 3h30
- 26/08/2020 - Roll bar - 1h
- 05/09/2020 - Making spacers for roll bar and drill rollbar - 5h
- 14/09/2020 - Finish drill roll bar - 3h
- 15/09/2020 - Cut and drill rails - 2h
- 17/09/2020 - Drill canopy slider block and frame - 2h
- 19/09/2020 - Slider rail and checking initial canopy fit - 2h
- 26/09/2020 - Bending canopy frame - 2h
- 21/10/2020 - More frame fitting, getting desperate - 8h
- 30/10/2020 - End of fitting, drill the sucker - 20H
- 03/11/2020 - Canopy centerline and latch hole - 4h
- 11/11/2020 - Initial canopy trimming - 6h
- 14/11/2020 - The Big Cut ! - 8h
- 15/11/2020 - Canopy trimming side and end - 6h
- 28/11/2020 - Frame bending compensation - 4h30
- 27/01/2020 - Measuring to get roll bar level - 3h
- 28/01/2021 - cutting excess from roll bar feet - 2h15
- 30/01/2021 - Roll bar support install - 5h30
- 03/04/2021 - Drilling canopy to canopy frame - 6h30
- 05/04/2021 - canopy frame work - 7h45
- 07/04/2021 - first windscreen impressions - 0h30
- 01/05/2021 - measuring cut locations windscreen - 1h
- 13/08/2021 - cutting windscreen 1 - 2h
- 28/08/2021 - More cutting windscreen - 7h
- 04/09/2021 - More cutting on the windscreen - 6h
- 18/09/2021 - slider cut - 3h30
- 22/09/2021 - windscreen cutting - 5h
- 23/09/2021 - drilling frame wheels to slider rail - 3h
- 29/09/2021 - Drilled the windscreen to the rollbar - 3h
- 01/10/2021 - contd drilling windscreen - 4h
- 02/10/2021 - some more tweaking - 4h
- 03/10/2021 - making windscreen attach clips - 2h30
- 05/10/2021 - countersinking windscreen holes - 3h
- 06/10/2021 - tapping the roll bar - 3h
- 14/10/2021 - Canopy latch work - 3h
- 15/10/2021 - Canopy latch mechanism, part 2 - 2h
- 22/10/2021 - Rear canopy blocks - 4h
- 01/11/2021 - rear canopy attach blocks pt 2 - 1h30
- 02/11/2021 - fine tuning slider rails - - 2h30
- 04/11/2021 - slider track - 3h
- 06/11/21 - side skirts pilot side - 7h
- 13/11/2021 - Sideskirts brace - 7h30
- 14/11/2021 - dimple countersink sideskirt - 2h
- 20/11/2021 - Working on passenger side skirt - 2h30
- 21/11/2021 - passenger side skirt pt2 - 5h
- 22/11/2021 - Passenger side skirt Pt3 - 0h30
- 23/11/2021 - Passenger side skirt Pt4 - 2h
- 25/11/2021 - Passenger side skirt Pt5 - 1h30
- 26/11/2021 - some help drilling - 1h
- 27/11/2021 - Passenger side skirt Pt7 - 3h30
- 08/01/2022 - Preparing for interior painting
- 22/01/2022 - Rivetting canopy to frame
- 29/01/2022 - Rivetting skirts
- 05/02/2022 - Starting rear skirts - 5h30
- 12/02/2022 - modelling for rear skirt - 2h
- 26/02/2022 - rear skirt epoxy first 3 layers - 8h
- 05/03/2022 - Rear skirts 2nd layer of epoxy - 4h
- 24/03/2022 - applying micro on rearskirts - 3h30
- 08/04/2022 - applying more micro on the rearskirt - 3h
- 09/04/2022 - Rear skirt cutting to shape - 3h
- 16/04/2022 - more sanding rear skirt and drilling holes - 2h
- 07/05/2022 - Drilling attach points rear skirts - 2h
- 28/05/2022 - Sikaflex rear skirt - 5h
- 18/06/2022 - Rivetting canopy to frame in rear skirt and epoxy - 3h
-
4. Landing gear
- 06/08/2022 - Landing gear started - 5h45
- 13/08/2022 - U-810 cleaning and adapting - 2h
- 19/08/2022 - brake cylinder mating - 1h
- 27/08/2022 - parking brake mount - 4h
- 07/09/2022 - parking brake line bending - 2h
- 26/12/2022 - Refit right wheel tyre - 4h30
- 28/12/2022 - Fitting wheels on gear legs - 4h
- 29/12/2022 - Fitting brakes on gear legs (cntd) - 4h
- 30/12/2022 - Install left wheel on gear - 4h
- 31/12/2022 - Drill right axle gear leg wheel nut - 4h
- 02/01/2023 - Drill axle and install ADAHRS bracket - 1h30
- 03/01/2023 - Mount wheel and parking brake brachet - 2h
- 04/01/2023 - Landing gear clearence in firewall - 2h
- 07/01/2023 - parking brake elbows - 1h
- 15/01/2023 - Installing brake lines cabin side - 8h
- 26/03/2023 - Standing on her own legs ! - 3h30
- 27/03/23 - FFW pilot side brake line - 2h
- 28/03/2023 - FFW Passenger side brake lines - 1h30
-
5. Fairings
-
6. Wing tips
How to use
Use the kit buttons in the top ribbon bar to see a chronological overview per sub section per kit. For the full chronological article list, see chronological build link in prelude menu here below. The easiest way to lookup information is by typing in some part numbers or keywords using the search option in the ribbon bar
Caution !
Some advice on reading my log for fellow builders !
In some articles, I made corrections at later date on the original article to rectify my own stupidities or faults. Read through the entire article if you intend to use my findings/experiences on your own project !
Other content
Social Networking
Legal Mumbo-Jumbo
It’s possible (not likely) that I’m not as smart as I think I am. (Occasionally, I have moments when I know this to be true. Fortunately, the feeling passes quickly.) Although I have tried to make this information as accurate as I can, it is not only possible, but also quite likely, that erroneous and misguided information lurks within these pages. I cannot and do not warrant these pages to be error free and correct. Furthermore, I accept no liability for the use of this (mis)information. And, as many would say, your mileage may vary. If, after reading this, you are intent on proceeding, please be aware that the contents of this site are protected by copyright (copyright © 2011 and 2012). Nonetheless, you may copy this material subject to these two conditions: (1) any information used is for non-commercial purposes, and (2) the source of the material is properly credited. Of course, you may link to any page herein. At some articles, snippets of the plans from Vans are visible. These are for educational and illustrations purposes only and should never be used as plans for part construction or assembly as plans may have changed since the picture was taken and more important they are protected by Copyright by the Vans Aircraft Mothership company.